Apply straight downward pressure to each end of the cap while sliding into the closed position. To help you make informed decisions about More information. Recommended Forklift Free System Features for Proper Safety and Ergonomic Operation When re-designing material handling flow to address restricted use of forklifts Forklift Free , equipment ergonomics and safety play a key role. The pallet jacks you are servicing. Inspect motor casings for excessive wear and cracks Inspect motor slide caps for excessive wear and deformation Visually check all welds Head section Foot section Main Frame Check joints between sleeping surface sections for loose fasteners. A01 Copyright Dell, Inc. Insert one locking and one non-locking caster into each bed end. Your particular model may have only some of these More information.
S21F acid bath cleans grease and oil from metal. Grid deck not shown for clarity 3. Read the entire manual carefully before using your bed, and refer to it during use if you have questions. Before operating this lift, read and understand this Operator s Manual. Slide the head and foot sections together until the foot section’s hook catches the head section s rivet on both sides. Failure to follow the safety rules and other basic More information. Rack installation instructions Review the documentation that comes with the rack cabinet for safety and cabling information.
Ensure that all four corners of each slide cap are engaged.
BED SERVICE PARTS – Lumex Syatems US User Manual – Page 20 of 24 |
Assemble bed ends 1. Position spring-loaded crossbrace B into slots G2 on both sides of bed. Power cord Pendant hand control cord Check to ensure that all plugs are fully inserted or attached. If the linkage locks, manually push h7902se large linkage plate toward the foot of the bed. When using nasal or masked type administering equipment, oxygen or air tubing MUST be routed and secured properly to ensure that tubing does NOT become entangled and eventually severed during normal operation of bed.
Quarter Rail The Quarter Rail, approximately 18 inches in length when mounted on the Patriot bed, can be used as a head assist, head rail, or foot homecae. Carefully read these instructions before installing your new air-conditioner. Vancouver Model NameModel No.
The pendant hand control cord must be routed and secured properly to ensure that the cord does NOT become entangled and eventually severed during use. Failure to do so can result in serious injury. Do not allow this device to be operated by small children. The warranty does not include any labor charges incurred in replacement part s installation or any associated freight or shipping charges to the manufacturer.
To order service parts, contact our Customer Service department at fax. While it is possible to install the motor backwards, avoid it! Lower bed to its lowest height.
Incorrect installation could cause the bed to move in unexpected ways. Your particular model may have only some of these More information. When coupling and shaft are aligned, unlock spring-loaded coupling. There are additional safety statements in other chapters or sections, which may be the same as or similar to the following, or specific to the operations. Start display at page:. The Okimat actuator casing may feel warm to the touch even when the bed is not being used; this is a pattriot condition.
Release spring button to lock it into hole. Ensure spring buttons face inward as shown above. When using telescoping deck-mount bed rails, the head and knee may not lower without weight on the bed.
QuiliRinse seals metal for powder coating. Allen key supplied Panel colours gomecare illustration purposes. Do not lie, sit or lean in such a way that your entire body weight is placed only on the raised head or foot sections of the bed.
Motor comes from factory with pendant hand control plugged into motor.
Lumex Syatems US0208 User Manual
All parts are then coated with a colored epoxy powder and baked homdcare minutes at degrees F. Repeat step 8 for the other cap.
Align motor and gearbox After installing foot end, you may have to shift bed frame slightly in bed end hooks to ensure proper horizontal pqtriot with motor coupling and end gearbox shaft. Read the entire manual carefully before using your bed, and refer to it during use if you have questions. Check all bolts and tighten as needed. Every MGB body is slightly different More information.
Save this manual More information. Inspect motor casings for excessive wear and cracks Inspect motor slide caps for excessive wear and deformation Visually check all welds Head section Foot section Main Frame Check joints between sleeping surface sections for loose fasteners.
Bed Service Parts – Lumex PATRIOT US User Manual [Page 24]
Position head wing as shown above. EqualLogic is a registered trademark. Failure to follow these inspection procedures can cause personal injury and property damage. Lower bed onto corner lock as shown at above right.
Before operating, ensure that the bed frame rivets are properly seated in the bed end hooks; otherwise, injury or damage may result. Head Foot Remove motor slide caps slide cap motor Remove motor slide caps 1. Box Saco, ME.